Just about every person seems to have his or her own conception when it comes to How to Install a Bathtub Yourself.
Mounting a bathtub isn't specifically rocket science, but it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently accessible, the project can relocate easily; if you need to open up a wall to get rid of the old tub and position the new bathtub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require a helper to vacate the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job as well as fit trying it. Instead of employing a service provider to take control of a halfway-completed task, it is much better to think about using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly help you set up a new bath tub in your washroom if you have already gotten a brand-new tub as well as do not require to change the plan of your previous water pipelines.
Your tools and material checklist must comprise the following:
Preparing for the Setup
To start with, the sustaining framework supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must now prepare to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is disconnect the water supply. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be fairly problematic as a result of the limited accessibility that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will originate from the pipes. Once the supply pipelines have been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Installing the Bathtub
Using both wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in equally spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet connector to the suitable supply pipe by making a compression sign up with; after that do the same for the other faucet.
Turn on the supply of water as well as inspect all joints and also brand-new pipework for leaks and tighten them if needed. Fill the bathtub and likewise check the overflow outlet and the regular outlet for leaks.
Finally, take care of the bathroom paneling as defined in the maker's instruction manual. Tiling as well as securing around the bathtub should wait till the tub has actually been utilized at least once as this will certainly resolve it into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin making sure that the washers remain in place in between the faucet and also the sink. Protect the faucet in position with the manufacturer provided backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet ports. The previous kind needs to be connected to the faucet ends first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a stiff seal, creating the water to permeate the wall surface between the bathroom and also the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and cartridges, and are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealer can break fairly very early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly readily available on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or waterproof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted reader on How to Install a Bathtub, I was thinking sharing that post was important. Are you aware of another individual who is curious about Tools You Need to Install a New Bathtub ? Why not share it. Thanks a bunch for your time. Please come by our blog back soon.
Top-notch fix? Dial!